Residential

EV charger installation in Orleans and Ottawa

Home EV charger installation by a licensed and insured Master Electrician. We check what your panel can carry before anything is installed.

  • Master Electrician
  • ESA compliant
  • Licensed and insured
  • BBB Accredited, A+ rated

Overview

A charger circuit your home can carry

A home charger is one of the largest loads a house takes on, so the work starts at the panel. We look at what your panel already carries, then plan the circuit, the charger location and the run between them. If there is not enough room, a panel upgrade comes first and is planned as part of the same job. Every installation is ESA compliant. Request a quote with your panel size and where you park. For a workplace, a fleet or a multi-unit building, see commercial EV charger installation in Ottawa. For typical price ranges and permit rules, see EV charger installation costs in Ottawa.

Tesla Wall Connector on a plywood backing beside its disconnect, installed by VB Electric
Tesla Wall Connector with its disconnect

What is included

What the installation covers

  1. 01

    Load calculation

    Rule 8-200 adds the basic load, the greater of electric heat and air conditioning, the range, and the charger at 100% of its rating when no energy management system is used.

  2. 02

    Dedicated circuit

    Rule 86-300 puts the charger on its own branch circuit, unless an energy management system shares one. A 48 amp setting uses a 60 amp breaker. A 32 amp setting uses a 40 amp breaker.

  3. 03

    Charger mounting

    Level 2 charging is 208 or 240 volts. SAE J1772 is the connector on most of these chargers. NACS is the connector Tesla vehicles use, and other makers have been adopting it since 2022. Have a charger already, or still choosing? Tell us on the form.

  4. 04

    ESA filing

    The Licensed Electrical Contractor files the notification with the Electrical Safety Authority before the work starts. A new charger circuit is not a like-for-like replacement under Rule 2-005.

Before you book

Good to know

Panel capacity
ESA's worked example of a 32 amp, 240 volt charger on a house of 140 square metres comes out to 108.6 amps, and the minimum service is then 125 amps. A 100 amp service is below that. A 200 amp service is above it.
Charger
Have one already or still choosing? Tell us on the form.
Location
The distance from the panel to where you park shapes the job, so tell us where the charger should go.

Questions

EV charger installation questions

Do I need a panel upgrade for an EV charger?

Not always. With no energy management system, the charger is added at 100% of its rating. In the ESA example, a 32 amp charger at 240 volts is 7,680 watts, the house calculates to 108.6 amps, and the minimum service is 125 amps. A 100 amp service does not cover that example. A 200 amp service does. An energy management system that monitors the service can limit the charger to a set maximum instead.

What is a load calculation?

For a single dwelling it is the Rule 8-200 total: 5,000 watts for the first 90 square metres and 1,000 watts for each further 90, the greater of electric heat and air conditioning, an electric range at 6,000 watts when it is rated up to 12 kilowatts, the charger at 100% when no energy management system is used, and other loads such as a dryer and a storage water heater at 25%. It is done before the installation is quoted.

Do you take care of the permit and ESA inspection?

Yes. A new charger circuit is filed with the Electrical Safety Authority before the work starts. The Licensed Electrical Contractor files it. The homeowner does not file it for the contractor.

Do you supply the charger, or only install it?

Have a charger already, or still choosing? Tell us on the form. The circuit is sized to the charger you name.

Which chargers and connectors do you install?

Level 2 is 208 or 240 volts. SAE J1772 is the connector on most Level 1 and Level 2 chargers in Canada. NACS is the Tesla connector. It has been open to other makers since 2022, and NRCan calls it a preferred connector for vehicles in Canada. A Tesla needs an adapter for a J1772 charger, and other vehicles need an adapter for a Tesla Level 2 charger. On a Tesla Wall Connector, a 60 amp breaker is a 48 amp output, a 50 amp breaker is 40 amp, and a 40 amp breaker is 32 amp. Tell us the make and model on the form.

Who does the work?

Vincent Bourdeau, a licensed and insured Master Electrician. Every installation is ESA compliant.

How it works

From quote to ESA filing

  1. 01

    Request

    Tell us about your panel, your charger and where you park.

  2. 02

    Load calculation

    We confirm what the panel can carry and quote the work.

  3. 03

    Installation

    We run the circuit and mount and connect the charger.

  4. 04

    ESA

    The notification is filed with the Electrical Safety Authority before the work starts.

Request a quote

Plan your home EV charger

Tell us about your panel and where you park.